Dripping tap? How to fix it, and when to replace it

A dripping tap usually needs a new washer or ceramic cartridge. How to tell which type you have, isolate the water, swap the part and deal with limescale.

Plumbing · · By the Green PHS team

Plumber working on the pipework and isolation valves under a sink

A dripping tap almost always means one worn part: a rubber washer in a traditional tap, or a ceramic cartridge in a modern quarter-turn or lever tap. Both are cheap and, with the water isolated, you can often replace them yourself in under an hour. The first job is working out which type of tap you have.

It is worth fixing sooner rather than later. A steady drip wastes water all day, adds to your bill if you are on a meter, and leaves limescale stains in the sink. A drip from the hot tap also wastes the energy used to heat that water.

Which type of tap do you have?

How the tap turnsTypeUsual cause of a drip
Several full turns from off to fully on, and it gets stiffer as you close itTraditional washer tap (compression tap)Worn rubber washer or seat
A quarter or half turn from off to fully onCeramic disc tapWorn or scaled ceramic cartridge
A single lever controlling hot and cold togetherMixer cartridge tapWorn mixer cartridge or seals

If water leaks from around the handle or spout rather than out of the end of the spout, it is usually a worn O-ring or gland seal, not the washer or cartridge.

How to isolate the water

Never take a tap apart with the water on.

  1. Look for isolation valves on the pipes under the sink or basin. They are small fittings with a screw slot or a little handle. Turn them a quarter turn so the slot sits across the pipe.
  2. If there are no isolation valves, turn off the main stopcock for cold taps. Our guide on how to find your stopcock shows where to look. For hot taps fed from a tank in the loft, you may need to close a gate valve on the pipe from the cylinder, or turn off the stopcock and drain the hot water down.
  3. Open the tap fully to let the remaining water run out and confirm the supply is off.
  4. Put the plug in. It stops small screws and parts disappearing down the drain.

Fixing a dripping washer tap

  1. Prise off the decorative cap on top of the handle and undo the screw underneath. Lift off the handle.
  2. Unscrew the shroud, if there is one, to expose the headgear (the large brass nut).
  3. Hold the tap body steady with one hand, or with a grip wrapped in a cloth to protect the finish, and undo the headgear with a spanner.
  4. The washer is on the bottom of the headgear, held by a small nut or pushed on. Remove it and fit a new one of the same size. Washer kits from a hardware shop come in common sizes.
  5. Look at the brass seat inside the tap body. If it is pitted or grooved, a new washer will soon fail again; seats can be reground or a reseating kit fitted.
  6. Reassemble, open the isolation valve slowly and test.

Replacing a ceramic cartridge

  1. Remove the handle. There is often a grub screw underneath or behind it, or a screw under a cap on top.
  2. Unscrew the cartridge with a spanner. Take care: on some taps one of the cartridges is reverse threaded.
  3. Take the old cartridge to a plumbers’ merchant to get an exact match. Cartridges vary by brand, spline count, length and which way they turn, and the wrong one will not fit or will turn the wrong way.
  4. Fit the new cartridge hand-tight, then nip it up gently with the spanner. Over-tightening can crack it.
  5. Refit the handle, turn the water back on slowly and test both hot and cold.

Sometimes the cartridge is fine and the drip comes from scale or grit on the ceramic discs or the rubber seal at its base. Cleaning the cartridge can stop the drip for a while, but a worn one will usually need replacing.

Limescale: why a dripping tap comes back

London has hard water, and it is hard on taps. Scale builds up on washers, seats and ceramic discs, stops them sealing and makes handles stiff. A few habits help:

  • Do not over-tighten taps to stop a drip. It flattens washers and strains cartridges, making the drip worse in the end.
  • Wipe taps dry and descale aerators and spouts regularly with a diluted descaler or white vinegar.
  • If your taps scale up quickly, a scale reducer on the incoming supply can help. Our hard water and limescale guide explains how scale affects the whole system.

When is a new tap the better option?

Replacing a washer or cartridge is usually the cheaper fix, but sometimes a new tap makes more sense:

  • The tap body is cracked, corroded or leaking from the base
  • The spare cartridge is no longer made, or costs close to what a new tap does
  • The tap has been repaired several times and keeps going
  • Parts are seized solid with scale and will not come apart without damage
  • You were planning to change the sink or bathroom anyway

If you are replacing taps as part of a refit, our bathroom installation team can supply and fit them with the rest of the work.

When to call an engineer

  • You cannot isolate the water, or the isolation valve itself is leaking
  • The headgear or cartridge is seized and will not move without force
  • You have fitted a new washer or cartridge and it still drips
  • Water is leaking under the sink or into the cabinet, not just from the spout
  • It is a wall-mounted or concealed tap where the body sits behind tiles

Our tap repair service covers all types, from old pillar taps to modern mixers. Labour is £120 an hour including VAT on weekdays from 8am to 5pm, with parts at cost plus 20%; see the prices page for the full details.

If you are not sure what type of tap you have, call Lee on 020 8050 5913. He can usually tell you what part you need over the phone, at no charge.

Stuck? Call Lee.

If you are not sure it is safe, stop and call. Advice by phone is free.

020 8050 5913

Related services

Our work on these jobs

See the gallery
  • Basin tap on a vessel basin and wood vanity unit
  • Under-sink water heater and new plumbing in a kitchen cupboard
  • Plumber working under a kitchen sink
  • Finished bathroom with a freestanding bath and wall-hung toilet

Photographs of jobs completed by Green PHS engineers.

More advice

Call Lee. He picks up.

Tell him what is happening. If it is a quick fix, he will talk you through it for free. If not, we will get an engineer to you, usually the same day.

Call Lee Get a quote